液压登车桥应严格遵守超重，超负荷工作可能造就人和物的损伤；

The hydraulic boarding bridge shall strictly abide by the principle of overweight, and overload work may cause damage to people and objects;

在没有护栏的升降平台上工作，可能会使人员下坠，造就人员伤亡。

Working on the lifting platform without guardrail may cause personnel to fall and cause casualties.

为保证液压登车桥处于良好工作状态，使用前应提前做检查：主要包括控制按钮是否灵验；电源线及插座是否完好；输油管是否完好；护栏的稳固性；各交接点螺栓的紧固性；外观质量的完好。但当电源接通，指示灯亮后，按上升按钮，电机转动而升降台不上升，这可能是三相电源接反后电机倒转，只需电源纠正即可，所以不是大问题。

In order to ensure that the hydraulic boarding axle is in good working condition, check in advance before use: mainly including whether the control button is effective; Whether the power cord and socket are intact; Whether the oil pipeline is intact; Stability of guardrail; Tightness of bolts at each junction point; The appearance quality is intact. However, when the power supply is turned on and the indicator light is on, press the rise button, the motor rotates and the lifting table does not rise. This may be that the motor reverses after the three-phase power supply is connected reversely. It only needs to be corrected by the power supply, so it is not a big problem.

液压登车桥工作时须撑开支腿，调整支腿螺栓，使升降平台平稳受力于支腿并保持水平；在升降过程中和升起状态下，不得移动升降平台，严禁在升降平台上摇晃。

When the hydraulic support leg is lifted and lowered on the platform, the hydraulic support leg must be adjusted and kept horizontal; During the lifting process and in the lifting state, the lifting platform shall not be moved and shaking on the lifting platform is strictly prohibited.

液压登车桥工作时有异常声响，应立即停机检查，以免造成升降台严重破坏；使用前须检查电气设备是否正常；凡是轴销油孔，每次使用前须加润滑油。使用前须先作空载升降，检查液压系统是否正常；工作台载重不得大于额定值，更不能做激烈的人为摇晃；油箱内的液压油每工作500小时须更换一次。

If there is abnormal sound when the hydraulic boarding bridge works, stop the machine immediately for inspection to avoid serious damage to the lifting platform; Check whether the electrical equipment is normal before use; Lubricating oil must be added to all axle pin oil holes before each use. No load lifting and lowering must be carried out before use to check whether the hydraulic system is normal; The load of the workbench shall not be greater than the rated value, let alone violent artificial shaking; The hydraulic oil in the oil tank must be replaced every 500 hours.

登车桥工作结束后，应将各部擦洗清洁，不作业时应将工作台下降低位置。

After boarding the axle, all parts shall be scrubbed and cleaned. When not working, the workbench shall be lowered to the low position.

液压登车桥每月保养：滚轮、中间轴及轴承，油缸销轴及轴承，臂架铰轴及轴承等有无磨损；液压油的油质和油位；液压登车桥全程升起，在这位置时，液压面应高出箱底40-50毫米。液压油是变暗、发粘或有砂砾等异物，如有发现应及时更换；各部位均加注一些润滑油，延长轴承使用寿命。液压登车桥用途广泛，做好以上几点不但可以保障您的人身还可以延长设备的使用寿命，让登车桥更好的为您服务。

Monthly maintenance of hydraulic boarding bridge: whether the roller, intermediate shaft and bearing, oil cylinder pin shaft and bearing, boom hinge shaft and bearing are worn; Oil quality and oil level of hydraulic oil; The hydraulic boarding axle is raised in the whole process. In this position, the hydraulic surface should be 40-50mm higher than the bottom of the box. The hydraulic oil is dark, sticky or has foreign matters such as gravel. If it is found, it should be replaced in time; All parts are filled with some lubricating oil to prolong the service life of the bearing. The hydraulic boarding bridge has a wide range of uses. Doing well in the above points can not only ensure your personal safety, but also prolong the service life of the equipment and make the boarding bridge serve you better.

以上就是为大家介绍的有关移动登车桥的详细介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以的态度,为您提供服务

The above is a detailed introduction to the mobile boarding axle. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service